openWB Embedded software replacement

← Caricabatterie Nessun token sponsor richiesto

Replacement for the OpenWB software, when evcc runs directly on the OpenWB hardware. Currently supported Hardware is OpenWB Series2. mA control is used automatically if the EVSE firmware supports it.

Please be aware that installing evcc on the OpenWB Hardware will void your guarantee!

Installation without display:

Install and configure Raspberry Pi OS Lite (64bit) image.

Add the following at then end of /boot/firmware/config.txt:

[all]
gpio=4,5,7,11,17,22,23,24,25,26,27=op,dl
gpio=6,8,9,10,12,13,16,21=ip,pu

Install evcc according to the manual.
Add the groups required for user evcc to access the hardware: usermod -a -G gpio,dialout,input evcc
Configure evcc according to the manual. There are multiple distinct Hardware versions, which differ regarding the built-in modbus adapters and charge meters.
- A single or multiple Modbus adapters are found at /dev/ttyUSB0, /dev/ttyUSB1 (some Duo) or /dev/ttyACM0. Some Duo's contain two Modbus adapters, some just one.
- The EVSE for the first connector has always the ID 1, the one for the second ID 2.
- The different possible charge meters are:
  - Bernecker Engineering MPM3PM (template: mpm3pm) with ID 5 or ID 6 for the Duo's second connector.
  - SDM630/SDM72 (template: eastron) with ID 105 or ID 106 for the Duo's second connector.
  - ABB B23 (template: abb-ab) with ID 201

Additional steps for showing evcc on the display (be careful, because this will allow anybody to enable charging!). User pi is just an example here, replace it with the user actually used:

apt install labwc wayfire seatd xdg-user-dirs firefox-esr swayidle wlopm

Create the file /home/pi/.config/labwc/autostart with the following contents:

/usr/bin/firefox-esr --kiosk http://localhost:7070/ &
/usr/bin/swayidle -w timeout 600 'wlopm --off \*' resume 'wlopm --on \*' &

Create file /home/pi/.config/systemd/user/kiosk.service with the following content:

[Unit]
Description=Start Kiosk mode
[Service]
Type=simple
ExecStart=/usr/bin/labwc
[Install]
WantedBy=default.target

Enable autostart of kiosk mode: systemctl --user enable kiosk
As root: Enable start of systemd user units without the user having to log-in: loginctl enable-linger pi

At https://github.com/evcc-io/images complete images for both variants are available.

Funzionalità supportate

Regolazione mA: Regolazione più fine della corrente di ricarica (mA invece di A) per sfruttare meglio il surplus solare.
RFID: Lettore di tessere RFID integrato per l’identificazione del veicolo.
1P/3P: Commutazione automatica delle fasi. Utile per la ricarica con surplus solare.
Riducibile: La potenza assorbita può essere ridotta (ad es. § 14a EnWG). Vedi Limite esterno.

Parametri

Modbus

Nome	Descrizione	Valore	Livello
`id`	ID Modbus Predefinito: `1`	int	obbligatorio
`device`	Nome dispositivo Adattatore USB-RS485 Esempio: `/dev/ttyUSB0`		obbligatorio
`baudrate`	Baudrate Predefinito: `9600`		obbligatorio
`comset`	ComSet Parametro di comunicazione dell’adattatore Predefinito: `8N1`		obbligatorio
`host`	Indirizzo IP o hostname Esempio: `192.0.2.2`		obbligatorio
`port`	Porta Predefinito: `502`	int	obbligatorio
`phases1p3p`	Phase switching Charger is equipped with phase switching feature		facoltativo
`rfid`	RFID card reader USB VID:PID RFID card reader USB VID:PID value (as be obtained from lsusb), leave empty for no RFID card reader Esempio: `413d:2107`		facoltativo
`cpwait`	Duration of CP interruption when phase-switching and waking up car. Minimum 5 seconds. Predefinito: `10s`		avanzato
`connector`	Connector number For multi-connector stations. Numbering starts at 1. Predefinito: `1`		avanzato

Esempio di configurazione per evcc.yaml

Se preferisci non configurare il dispositivo dall’interfaccia, puoi usare questo blocco YAML.

chargers:
    - name: my_charger
      type: template
      template: openwb-native

      # RS485 via adapter (Modbus RTU)
      modbus: rs485serial
      id: 1
      device: /dev/ttyUSB0 # USB-RS485 Adapter Adresse
      baudrate: 9600 # Prüfe die Geräteeinstellungen, typische Werte sind 9600, 19200, 38400, 57600, 115200
      comset: "8N1" # Kommunikationsparameter für den Adapter

      # RS485 via TCP/IP (Modbus RTU)
      modbus: rs485tcpip
      id: 1
      host:  # Hostname
      port: 502 # Port
      phases1p3p: # Phase switching, Charger is equipped with phase switching feature (optional)
      rfid: 413d:2107 # RFID card reader USB VID:PID, RFID card reader USB VID:PID value (as be obtained from lsusb), leave empty for no RFID card reader (optional)
      cpwait: 10s # Duration of CP interruption, when phase-switching and waking up car. Minimum 5 seconds. (optional)
      connector: 1 # Connector number, For multi-connector stations. Numbering starts at 1. (optional)