Cupra EU Data Act

← Voertuigen

Uses the vehicle data provided under the EU Data Act through the VW group portal. Log in with the credentials of the My CUPRA App.

Prerequisite (one-time, in a browser): log in to the portal, confirm the consent screen, link the vehicle and enable a continuous data request (every 15 minutes). Without this activation the portal returns no data. Data is provided on the portal roughly every 15 minutes.

Parameters

Naam	Omschrijving	Niveau
`user`	Username e.g. email address, user id, etc.	optioneel
`password`	Password Service account password	optioneel
`vin`	Vehicle Identification Number If you own multiple vehicles from the same manufacturer Voorbeeld: `W...`	optioneel
`title`	Title Will be displayed in the user interface	optioneel
`capacity` [kWh]	Battery capacity Voorbeeld: `50`	optioneel
`icon`	Icon Will be displayed in the user interface Standaard: `car`	geavanceerd
`phases`	Maximum number of phases Used to determine the minimum solar surplus and plan duration.	geavanceerd
`minCurrent` [A]	Minimum current The minimum current per connected phase that can be used Voorbeeld: `6`	geavanceerd
`maxCurrent` [A]	Maximum current The maximum current per connected phase that can be used Voorbeeld: `16`	geavanceerd
`maxPower` [W]	Maximum charging power hint Defines the maximum charging power of the vehicle. Helps improve charge plan accuracy when the vehicle typically uses less than the offered current or supports higher single-phase current compared to three-phase. The offered current of the loadpoint is not affected. Voorbeeld: `10000`	geavanceerd
`identifiers`	RFID identification Used to assign the vehicle to a loadpoint via RFID card. The identifier is shown on the loadpoint. Copy the value from there. Learn more.	geavanceerd
`priority`	Priority Priority of the loadpoint or vehicle in relation to other loadpoints or vehicles for allocating surplus energy (higher values, higher priority).	geavanceerd
`cache`	Cache Time interval for data refresh Standaard: `15m` Voorbeeld: `5m`	geavanceerd
`coarsecurrent`	1A current control Vehicle supports 1A current steps only	geavanceerd
`welcomecharge`	Charge on connection Charger will enable charging for short time when vehicle is connected, irrespective of configured charge mode. This is useful for vehicles that require power supply when connecting.	geavanceerd
`climaterdisabled`	Disable climater detection Ignore the vehicle's climater state for charge control, so charging stops at the SoC or energy limit even when the vehicle signals an active climater request.	geavanceerd
`autodetectdisabled`	Exclude from auto detection Ignore the vehicle for auto detection of connected vehicles	geavanceerd
`wakeupdisabled`	Disable wake-up calls Do not send wake-up calls to the vehicle or charger, useful for vehicles that refuse to charge after repeated wake-ups.	geavanceerd

Configuratievoorbeeld voor evcc.yaml

Als u niet via de gebruikersinterface wilt configureren, kunt u ook dit YAML-blok gebruiken.

vehicles:
    - name: my_car
      type: template
      template: cupra
      user: # Username, e.g. email address, user id, etc.
      password: # Password, Service account password
      vin: W... # Vehicle Identification Number, If you own multiple vehicles from the same manufacturer (optional)
      title: # Title, Will be displayed in the user interface (optional)
      capacity: 50 # Battery capacity (kWh), optional
      icon: car # Icon, Will be displayed in the user interface [car, bike, bus, moped, motorcycle, rocket, scooter, taxi, tractor, rickshaw, shuttle, van, airpurifier, battery, bulb, climate, coffeemaker, compute, cooking, cooler, desktop, device, dishwasher, dryer, floorlamp, generic, heater, heatexchange, heatpump, kettle, laundry, laundry2, machine, meter, microwave, pump, smartconsumer, tool, waterheater] (optional)
      phases: # Maximum number of phases, Used to determine the minimum solar surplus and plan duration. [1, 2, 3] (optional)
      minCurrent: 6 # Minimum current (A), The minimum current per connected phase that can be used (optional)
      maxCurrent: 16 # Maximum current (A), The maximum current per connected phase that can be used (optional)
      maxPower: 10000 # Maximum charging power hint (W), Defines the maximum charging power of the vehicle. Helps improve charge plan accuracy when the vehicle typically uses less than the offered current or supports higher single-phase current compared to three-phase. _The offered current of the loadpoint is not affected._ (optional)
      identifiers: # RFID identification, Used to assign the vehicle to a loadpoint via RFID card. The identifier is shown on the loadpoint. Copy the value from there. [Learn more.](https://docs.evcc.io/en/docs/features/vehicle) (optional)
      priority: # Priority, Priority of the loadpoint or vehicle in relation to other loadpoints or vehicles for allocating surplus energy (higher values, higher priority). (optional)
      cache: 15m # Cache, Time interval for data refresh (optional)
      coarsecurrent: # 1A current control, Vehicle supports 1A current steps only (optional)
      welcomecharge: # Charge on connection, Charger will enable charging for short time when vehicle is connected, irrespective of configured charge mode. This is useful for vehicles that require power supply when connecting. (optional)
      climaterdisabled: # Disable climater detection, Ignore the vehicle's climater state for charge control, so charging stops at the SoC or energy limit even when the vehicle signals an active climater request. (optional)
      autodetectdisabled: # Exclude from auto detection, Ignore the vehicle for auto detection of connected vehicles (optional)
      wakeupdisabled: # Disable wake-up calls, Do not send wake-up calls to the vehicle or charger, useful for vehicles that refuse to charge after repeated wake-ups. (optional)