Sunsynk 3p hybrid inverter

Fonctionnalités prises en charge

Pilotage de la batterie: Pilotage externe de la charge et de la décharge de la batterie domestique par evcc.
Bridable: La production de l’onduleur peut être réduite (p. ex. § 9 EEG). Voir Limite externe.

Domaines d’utilisation

Compteur avant réseau
Production solaire
Batterie

Paramètres

Modbus

Nom	Description	Valeur	Niveau
`id`	ID Modbus Par défaut: `1`	int	obligatoire
`device`	Nom du périphérique Adaptateur USB-RS485 Exemple: `/dev/ttyUSB0`		obligatoire
`baudrate`	Débit en bauds Par défaut: `9600`		obligatoire
`comset`	ComSet Paramètre de communication de l’adaptateur Par défaut: `8N1`		obligatoire
`host`	Adresse IP ou nom d’hôte Exemple: `192.0.2.2`		obligatoire
`port`	Port Par défaut: `502`	int	obligatoire
`maxacpower` [W]	Maximum AC power of the hybrid inverter Par défaut: `0` Exemple: `5000`		facultatif
`batterytype`	Inverter for LV or HV batteries Choose "hv" if you are using a high voltage battery with a nominal voltage over 60V Par défaut: `lv`		facultatif
`maxdischargecurrent`	Max Discharge Current Maximum battery discharge current in Amperes (A) for normal mode. Typical range 50-350A depending on battery capacity. Power calculation: P(W) = Current(A) x Voltage(V). Example with 48V battery: 100A x 48V = 4800W (4.8kW). Par défaut: `100`		facultatif
`gridchargecurrent`	Grid Charge Current Maximum battery charging current in Amperes (A) from grid for charge mode. Typical range 30-350A depending on battery and inverter capacity. Power calculation: P(W) = Current(A) x Voltage(V). Example with 48V battery: 60A x 48V = 2880W (2.9kW). Par défaut: `60`		facultatif
`capacity` [kWh]	Battery capacity Exemple: `50`		facultatif
`minsoc` [%]	Minimum charge Lower limit as configured on the battery system. Used by optimizer. Par défaut: `0` Exemple: `25`		facultatif
`maxsoc` [%]	Maximum charge Upper limit as configured on the battery system. Used by optimizer and for grid charging. Par défaut: `100` Exemple: `95`		facultatif
`storageunit`	Battery storage unit index Par défaut: `1`		avancé
`maxchargepower` [W]	Maximum charge power For forced charging of the battery.		avancé
`maxdischargepower` [W]	Maximum discharge power Maximum discharge power of the storage.		avancé
`includegenport`	Treat GEN port as solar input When enabled, the GEN port of the inverter will be treated as an additional solar input. This will add the power and energy fed in through the GEN port to the total solar yield.		avancé
`firmware1098`	Firmware 1098 or newer (only for HV versions) After a firmware update of the high voltage inverter, some register values have changed their scaling factor. If your inverter has firmware version 1098 or newer, you need to enable this option to get correct values.		avancé

Exemple de configuration pour evcc.yaml

Si vous ne souhaitez pas passer par l’interface, vous pouvez utiliser ce bloc YAML à la place.

Compteur avant réseauProduction solaireBatterie

meters:
    - name: my_grid
      type: template
      template: deye-hybrid-3p
      usage: grid

      # RS485 via adapter (Modbus RTU)
      modbus: rs485serial
      id: 1
      device: /dev/ttyUSB0 # USB-RS485 Adapter Adresse
      baudrate: 9600 # Prüfe die Geräteeinstellungen, typische Werte sind 9600, 19200, 38400, 57600, 115200
      comset: "8N1" # Kommunikationsparameter für den Adapter

      # RS485 via TCP/IP (Modbus RTU)
      modbus: rs485tcpip
      id: 1
      host:  # Hostname
      port: 502 # Port

      # Modbus TCP
      modbus: tcpip
      id: 1
      host:  # Hostname
      port: 502 # Port
      batterytype: lv # Inverter for LV or HV batteries, Choose "hv" if you are using a high voltage battery with a nominal voltage over 60V [lv, hv]
      maxdischargecurrent: 100 # Max Discharge Current, Maximum battery discharge current in Amperes (A) for normal mode. Typical range 50-350A depending on battery capacity. Power calculation: P(W) = Current(A) x Voltage(V). Example with 48V battery: 100A x 48V = 4800W (4.8kW).
      gridchargecurrent: 60 # Grid Charge Current, Maximum battery charging current in Amperes (A) from grid for charge mode. Typical range 30-350A depending on battery and inverter capacity. Power calculation: P(W) = Current(A) x Voltage(V). Example with 48V battery: 60A x 48V = 2880W (2.9kW).
      includegenport: # Treat GEN port as solar input, When enabled, the GEN port of the inverter will be treated as an additional solar input. This will add the power and energy fed in through the GEN port to the total solar yield. (optional)
      firmware1098: # Firmware 1098 or newer (only for HV versions), After a firmware update of the high voltage inverter, some register values have changed their scaling factor. If your inverter has firmware version 1098 or newer, you need to enable this option to get correct values. (optional)

meters:
    - name: my_pv
      type: template
      template: deye-hybrid-3p
      usage: pv

      # RS485 via adapter (Modbus RTU)
      modbus: rs485serial
      id: 1
      device: /dev/ttyUSB0 # USB-RS485 Adapter Adresse
      baudrate: 9600 # Prüfe die Geräteeinstellungen, typische Werte sind 9600, 19200, 38400, 57600, 115200
      comset: "8N1" # Kommunikationsparameter für den Adapter

      # RS485 via TCP/IP (Modbus RTU)
      modbus: rs485tcpip
      id: 1
      host:  # Hostname
      port: 502 # Port

      # Modbus TCP
      modbus: tcpip
      id: 1
      host:  # Hostname
      port: 502 # Port
      maxacpower: 0 # Maximum AC power of the hybrid inverter (W)
      batterytype: lv # Inverter for LV or HV batteries, Choose "hv" if you are using a high voltage battery with a nominal voltage over 60V [lv, hv]
      maxdischargecurrent: 100 # Max Discharge Current, Maximum battery discharge current in Amperes (A) for normal mode. Typical range 50-350A depending on battery capacity. Power calculation: P(W) = Current(A) x Voltage(V). Example with 48V battery: 100A x 48V = 4800W (4.8kW).
      gridchargecurrent: 60 # Grid Charge Current, Maximum battery charging current in Amperes (A) from grid for charge mode. Typical range 30-350A depending on battery and inverter capacity. Power calculation: P(W) = Current(A) x Voltage(V). Example with 48V battery: 60A x 48V = 2880W (2.9kW).
      includegenport: # Treat GEN port as solar input, When enabled, the GEN port of the inverter will be treated as an additional solar input. This will add the power and energy fed in through the GEN port to the total solar yield. (optional)
      firmware1098: # Firmware 1098 or newer (only for HV versions), After a firmware update of the high voltage inverter, some register values have changed their scaling factor. If your inverter has firmware version 1098 or newer, you need to enable this option to get correct values. (optional)

meters:
    - name: my_battery
      type: template
      template: deye-hybrid-3p
      usage: battery

      # RS485 via adapter (Modbus RTU)
      modbus: rs485serial
      id: 1
      device: /dev/ttyUSB0 # USB-RS485 Adapter Adresse
      baudrate: 9600 # Prüfe die Geräteeinstellungen, typische Werte sind 9600, 19200, 38400, 57600, 115200
      comset: "8N1" # Kommunikationsparameter für den Adapter

      # RS485 via TCP/IP (Modbus RTU)
      modbus: rs485tcpip
      id: 1
      host:  # Hostname
      port: 502 # Port

      # Modbus TCP
      modbus: tcpip
      id: 1
      host:  # Hostname
      port: 502 # Port
      batterytype: lv # Inverter for LV or HV batteries, Choose "hv" if you are using a high voltage battery with a nominal voltage over 60V [lv, hv]
      maxdischargecurrent: 100 # Max Discharge Current, Maximum battery discharge current in Amperes (A) for normal mode. Typical range 50-350A depending on battery capacity. Power calculation: P(W) = Current(A) x Voltage(V). Example with 48V battery: 100A x 48V = 4800W (4.8kW).
      gridchargecurrent: 60 # Grid Charge Current, Maximum battery charging current in Amperes (A) from grid for charge mode. Typical range 30-350A depending on battery and inverter capacity. Power calculation: P(W) = Current(A) x Voltage(V). Example with 48V battery: 60A x 48V = 2880W (2.9kW).
      capacity: 50 # Battery capacity (kWh), optional
      minsoc: 0 # Minimum charge (%), Lower limit as configured on the battery system. Used by optimizer. (optional)
      maxsoc: 100 # Maximum charge (%), Upper limit as configured on the battery system. Used by optimizer and for grid charging. (optional)
      storageunit: 1 # Battery storage unit index, [1, 2] (optional)
      maxchargepower: # Maximum charge power (W), For forced charging of the battery. (optional)
      maxdischargepower: # Maximum discharge power (W), Maximum discharge power of the storage. (optional)
      includegenport: # Treat GEN port as solar input, When enabled, the GEN port of the inverter will be treated as an additional solar input. This will add the power and energy fed in through the GEN port to the total solar yield. (optional)
      firmware1098: # Firmware 1098 or newer (only for HV versions), After a firmware update of the high voltage inverter, some register values have changed their scaling factor. If your inverter has firmware version 1098 or newer, you need to enable this option to get correct values. (optional)

Voir la version nightly