openWB Embedded software replacement

← Chargeurs Aucun jeton de parrain requis

Replacement for the OpenWB software, when evcc runs directly on the OpenWB hardware. Currently supported Hardware is OpenWB Series2. mA control is used automatically if the EVSE firmware supports it.

Please be aware that installing evcc on the OpenWB Hardware will void your guarantee!

Installation without display:

Install and configure Raspberry Pi OS Lite (64bit) image.

Add the following at then end of /boot/firmware/config.txt:

[all]
gpio=4,5,7,11,17,22,23,24,25,26,27=op,dl
gpio=6,8,9,10,12,13,16,21=ip,pu

Install evcc according to the manual.
Add the groups required for user evcc to access the hardware: usermod -a -G gpio,dialout,input evcc
Configure evcc according to the manual. There are multiple distinct Hardware versions, which differ regarding the built-in modbus adapters and charge meters.
- A single or multiple Modbus adapters are found at /dev/ttyUSB0, /dev/ttyUSB1 (some Duo) or /dev/ttyACM0. Some Duo's contain two Modbus adapters, some just one.
- The EVSE for the first connector has always the ID 1, the one for the second ID 2.
- The different possible charge meters are:
  - Bernecker Engineering MPM3PM (template: mpm3pm) with ID 5 or ID 6 for the Duo's second connector.
  - SDM630/SDM72 (template: eastron) with ID 105 or ID 106 for the Duo's second connector.
  - ABB B23 (template: abb-ab) with ID 201

Additional steps for showing evcc on the display (be careful, because this will allow anybody to enable charging!). User pi is just an example here, replace it with the user actually used:

apt install labwc wayfire seatd xdg-user-dirs firefox-esr swayidle wlopm

Create the file /home/pi/.config/labwc/autostart with the following contents:

/usr/bin/firefox-esr --kiosk http://localhost:7070/ &
/usr/bin/swayidle -w timeout 600 'wlopm --off \*' resume 'wlopm --on \*' &

Create file /home/pi/.config/systemd/user/kiosk.service with the following content:

[Unit]
Description=Start Kiosk mode
[Service]
Type=simple
ExecStart=/usr/bin/labwc
[Install]
WantedBy=default.target

Enable autostart of kiosk mode: systemctl --user enable kiosk
As root: Enable start of systemd user units without the user having to log-in: loginctl enable-linger pi

At https://github.com/evcc-io/images complete images for both variants are available.

Fonctionnalités prises en charge

Régulation en mA: Régulation plus fine du courant de charge (mA au lieu de A) pour mieux exploiter le surplus solaire.
RFID: Lecteur de cartes RFID intégré pour l’identification du véhicule.
1P/3P: Commutation automatique des phases. Utile pour la charge sur surplus solaire.
Modulable: La puissance consommée peut être réduite (p. ex. § 14a EnWG). Voir Limite externe.

Paramètres

Modbus

Nom	Description	Valeur	Niveau
`id`	ID Modbus Par défaut: `1`	int	obligatoire
`device`	Nom du périphérique Adaptateur USB-RS485 Exemple: `/dev/ttyUSB0`		obligatoire
`baudrate`	Débit en bauds Par défaut: `9600`		obligatoire
`comset`	ComSet Paramètre de communication de l’adaptateur Par défaut: `8N1`		obligatoire
`host`	Adresse IP ou nom d’hôte Exemple: `192.0.2.2`		obligatoire
`port`	Port Par défaut: `502`	int	obligatoire
`phases1p3p`	Phase switching Charger is equipped with phase switching feature		facultatif
`rfid`	RFID card reader USB VID:PID RFID card reader USB VID:PID value (as be obtained from lsusb), leave empty for no RFID card reader Exemple: `413d:2107`		facultatif
`cpwait`	Duration of CP interruption when phase-switching and waking up car. Minimum 5 seconds. Par défaut: `10s`		avancé
`connector`	Connector number For multi-connector stations. Numbering starts at 1. Par défaut: `1`		avancé

Exemple de configuration pour evcc.yaml

Si vous ne souhaitez pas passer par l’interface, vous pouvez utiliser ce bloc YAML à la place.

chargers:
    - name: my_charger
      type: template
      template: openwb-native

      # RS485 via adapter (Modbus RTU)
      modbus: rs485serial
      id: 1
      device: /dev/ttyUSB0 # USB-RS485 Adapter Adresse
      baudrate: 9600 # Prüfe die Geräteeinstellungen, typische Werte sind 9600, 19200, 38400, 57600, 115200
      comset: "8N1" # Kommunikationsparameter für den Adapter

      # RS485 via TCP/IP (Modbus RTU)
      modbus: rs485tcpip
      id: 1
      host:  # Hostname
      port: 502 # Port
      phases1p3p: # Phase switching, Charger is equipped with phase switching feature (optional)
      rfid: 413d:2107 # RFID card reader USB VID:PID, RFID card reader USB VID:PID value (as be obtained from lsusb), leave empty for no RFID card reader (optional)
      cpwait: 10s # Duration of CP interruption, when phase-switching and waking up car. Minimum 5 seconds. (optional)
      connector: 1 # Connector number, For multi-connector stations. Numbering starts at 1. (optional)